Search Results

The optimization of the vaporization and mixture formation process is of great importance for the development of modern gasoline direct injection (GDI) engines, because it influences the subsequent processes of the ignition, combustion and pollutant formation significantly. In consequence, the subject of this work was the development of a measurement technique based on the laser induced exciplex fluorescence (LIF), which allows the two dimensional visualization and quantification of the in-cylinder air/fuel ratio. A tracer concept consisting of benzene and triethylamine dissolved in a non-fluorescent base fuel has been used. The calibration of the equivalence ratio proportional LIF-signal was performed directly inside the engine, at a well known mixture composition, immediately before the direct injection measurements were started.

Fine packaging is important for the bicycle transmission design. We are proposing a split power continuously variable transmission (SPCVT) operated with one mode. The planetary gear unit (PGU) in the SPCVT consists of two epicyclic gear trains. Both epicyclic gear trains do not include any ring gears to minimize the overall diameter of the transmission. A variator is connected to the PGU as a type of variable bridge. The variator involves two rotor pairs contacting on concave-convex spherical surfaces. This new mechanism of the variator shows a strong possibility to get high power density in comparison with other existing traction drives. A four-bar linkage is used to locate the counter rotor assembly exactly in the contact points of the rotor pair and extend the range of variator speed ratio. The crank is pulled by the wire connected to the speed control lever on the handle of bicycle.

Increased torque values passing from engine to transmission have, increasingly become a problem regarding shaft misalignment. Engineers are restricted with regard to applying ISO standards when investigating bearing life cycles as they tend only to cover normal [radial thrust] load conditions. Depending on the application, the need has arisen for numerical models to determine reduction in normal life cycles due to abnormal running conditions. The Simulia Finite Element package Abaqus v6.7 provides trends in the deformations, contact pressures and their respective distribution. It was found the most efficient profile, with regards to a uniform contact pressure, under both radial and misaligned conditions is the toroidal profile.

A very high power source solution was developed for the Non Line of Sight Launch System Container Launch Unit (NLOS-LS CLU). The power source solution has been shown to be capable of providing the required 72 continuous hours of operation and high power (3560 watts) to sustain launch capability. The power source consists of 18 BB-2590/U batteries connected in parallel in three layers. Several CLU battery systems have been delivered to the PEO and have been well accepted. The Army is using standard rechargeable batteries, is currently being upgraded with SMBus capability and higher capacity lithium-ion cells. For this reason, the CLU power source has been manufactured with SMBus capability. This paper will discuss the performance of one layer of the CLU power source to simulate the whole power load.

Examining the noise reduction of a motorcycle, the requirement of an effective method of reducing a drive chain noise has been a pending issue similarly to noise originating from an engine or exhaust system, etc. Through this study, it became clear that the mechanism of chain noise could be classified into two; low frequency noise originated from cordal action according to the degree of chain engagement and high frequency noise generated by impact when a chain roller hits sprocket bottom. An improvement of urethane resin damper shape, mounted on a drive side sprocket, was effective for noise reduction of the former while our development of a chain drive that combined an additional urethane resin roller with an iron roller worked well for the latter. The new chain system that combined this new idea has been proven to be capable of reducing the chain noise to half compared with a conventional system.

Beside the automotive industry, where 2-cylinder inline engines are catching attention again, twin-cylinder configurations are quite usual in the small engine world. From stationary engines and range-extender use to small motorcycles up to big cruisers and K-Cars this engine architecture is used in many types of applications. Because of very good overall packaging, performance characteristics and not least the possibility of parts-commonality with 4-cylinder engines nearly every motorcycle manufacturer provides an inline twin in its model range. Especially for motorcycle applications where generally the engine is a rigid member of the frame and vibrations can be transferred directly to the rider an appropriate balancing system is required.

Health related problems in over populated areas are a major concern and as such, there are specific legislations for noise generated by transport vehicles. In diesel powered commercial vehicles, the source for noise are mainly related to rolling, transmission, aerodynamics and engine. Considering internal combustion engine, three factors can be highlighted as major noise source: combustion, mechanical and tailpipe. The tailpipe noise is considered as the noise radiated from the open terminations of intake and exhaust systems, caused by both pressure pulses propagating to the open ends of the duct systems, and by vortex shedding as the burst leaves the tailpipe (flow generated noise). In order to reduce noise generated by vehicles, it is important to investigate the gas interactions and what can be improved in exhaust line design during the product development phase.

This paper focuses on the analysis and evaluation of acoustical design criteria to produce a plausible 3D sound field solely via headrest with integrated loudspeakers at the driver/passenger seats in the car cabin. Existing audio systems in cars utilize several distributed loudspeakers to support passengers with sound. Such configurations suffer from individual 3D audio information at each position. Therefore, we present a convincing minimal setup focusing sound solely at the passenger’s ears. The design itself plays a critical role for the optimal reproduction and control of a sound field for a specific 3D audio application. Moreover, the design facilitates the 3D audio reproduction of common channel-based, scene-based, and object-based audio formats. In addition, 3D audio reproduction enables to represent warnings regarding monitoring of the vehicle status (e.g.: seat belts, direction indicator, open doors, luggage compartment) in spatial accordance.

A large amount of heat is generated in electric vehicle battery packs during high rate charging, resulting in the need for effective cooling methods. In this paper, a prototype liquid cooled large format Lithium-ion battery module is modeled and tested. Experiments are conducted on the module, which includes 31Ah NMC/Graphite pouch battery cells sandwiched by a foam thermal pad and heat sinks on both sides. The module is instrumented with twenty T-type thermocouples to measure thermal characteristics including the cell and foam surface temperature, heat flux distribution, and the heat generation from batteries under up to 5C rate ultra-fast charging. Constant power loss tests are also performed in which battery loss can be directly measured.

The introduction of real driving emissions cycles and increasingly restrictive emissions regulations force the automotive industry to develop new and more efficient solutions for emission reductions. In particular, the cold start and catalyst heating conditions are crucial for modern cars because is when most of the emissions are produced. One interesting strategy to reduce the time required for catalyst heating is post-oxidation. It consists in operating the engine with a rich in-cylinder mixture and completing the oxidation of fuel inside the exhaust manifold. The result is an increase in temperature and enthalpy of the gases in the exhaust, therefore heating the three-way-catalyst. The following investigation focuses on the implementation of post-oxidation by means of scavenging in a four-cylinder, turbocharged, direct injection spark ignition engine. The investigation is based on detailed measurements that are carried out at the test-bench.

3M is committed to continuously improving products and their manufacture toward the goal of sustainability. The 3M Life Cycle Management (LCM) program has been established to implement this goal. It utilizes a matrix tool to facilitate the review. The matrix consists of LCM Stage (Material Acquisition, R&D Operations, Manufacturing Operations, and Customer Use/Disposal) and Impact (Environment, Health, Safety, and Energy/Resources). The program is coordinated at the staff level by the Corporate Product Responsibility group. The corporate goal is to apply LCM to all new and existing products. The LCM program started with evaluations of new products within business units. Since 3M produces more than 60,000 products manufactured from more than 10,000 different raw materials, the routine evaluation of individual products challenges available staff and business unit resources. A technology-based approach for doing LCMs has been implemented to meet the challenge.

This paper aims at providing the scientific community with an overview of the H2020 European project 3beLiEVe and of its early achievements. The project has the objective of delivering the next generation Lithium-Nickel-Manganese-Oxide (LNMO) battery cells, in line with the target performance of the “generation 3b” Li-ion battery technology, as per EU SET-plan Action 7. Its activities are organized in three main pillars: (i) developing the 3b next generation LMNO battery cell, equipped with (ii) an array of internal and external sensors and complemented by (iii) manufacturing and recycling processes at scale. At present, 3beLiEVe is approaching the completion of its first project year (out of a total project planned duration of 42 months). Hence this paper, beyond presenting the overall project’s structure and objectives, focuses on its earliest results in the fields of the cell material formulation, arrangement of sensors and design of the battery pack.

The present article is concerned with the investigation of the engine noise induced by the piston slap of an actual passenger car Diesel engine. The focus is put on the coherence of piston secondary movement, impact of the piston on the cylinder liner, generated structure-borne noise excitation of the engine structure and the occurring acceleration on the engine surface. Additionally, the influence of a varying piston-pin offset and piston clearance is evaluated. The analyses are conducted using an elastohydrodynamic multi-body simulation model, taking into account geometry, stiffness and mass information of the single components as well as considering elastic and hydrodynamic behavior of the piston-liner contact. A detailed description of the simulation model will be introduced in the article. The obtained results illustrate the piston secondary motion and the related structure-borne noise on the engine surface for several piston-pin offsets and piston clearances.

The objective of this project was to replace electromechanical power line contactors with a Static Transfer Switch (STS) to improve the transfer of electrical power between aircraft generators and decrease required maintenance. The switch requirements include high reliability, lightweight, and high speed (less than 15mS) power transfer. An STS can shorten the bus transfer time to less than the “ride-through” of aircraft electronic loads and therefore have the ability to control and transfer electrical power while maintaining critical mission requirements. The content of this paper and presentation will discuss the initial problem, the research and development approach, design, and initial testing of the STS.

The 42-Volt electrical system is being introduced in automobiles to provide the extra power needed for various electromagnetic devices. These paper discuses the opportunity offered by the 42Volt for powder metal parts and the challenges. Major opportunities are in motors. A brief discussion of motors and the performance requirements for the magnetic core material used is included. Brushless motor design can benefit the most from insulated iron powder compacts because of the design simplicity of powder metal parts and three dimensional flux capability which is most beneficial in rotating devices.(P/M stands for powder metallurgy and not permanent magnets)

The growing electrical power demands on bus electrical systems, such as the electric door operator, power steering, braking, air conditioning, windshield wipers, seat heating, and the need to improve emissions and fuel economy, are making current 12/24-volt electrical systems inadequate. For buses to continue to meet growing customer needs, electrical power must be increased. The industry is currently pursuing a 42-volt system as standard. In the U.S., that number (42 volts) was selected by an industry-wide research consortium led by the Massachusetts Institute of Technology. The switch to a 42-volt system would revolutionize the automotive industry. This would enable more electronic components and new technologies to be added to the vehicle. At the present time, the discussion and implementation of the 42-volt system is largely on luxury vehicles. The potential benefit of the system on heavy duty vehicles has not been fully explored.

A new electronically controlled transaxle has been put into production for Chrysler's family of LH cars. Among the attributes of this new transaxle are its ability to handle engines of high torque and high power coupled with high-speed shifts. Engine torque management is used in specific operating regimes. A feature of the transaxle is electronic modulation of the converter clutch. A number of logic features have been combined with hardware to provide good performance and shift quality over a wide operating range. An output transfer chain and a hypoid gear set are used to provide torque to the front wheels in a longitudinal power train orientation. Obtaining acceptable endurance life of the hypoid gears within an aluminum housing presented a significant challenge. New approaches were required to provide a chain-sprocket system with acceptable noise characteristics.

Demands for new features, increasing electrical loads, and improved fuel-economy are driving development of 42V PowerNets in automobiles. Shorter design cycles, increased complexity and a focus on quality are making robust design processes a strategic advantage for competitive manufacturers. Hardware prototypes are both time-consuming and inadequate for the task of verifying performance over a broad range of operating modes, environmental conditions and part-to-part variations. This paper outlines the use of an advanced design-flow, from idea to manufacturing, for vehicle power systems. It starts with the analysis of different topologies down to the subsystem modeling of a power window system. Finally it integrates everything to a Digital Mock-Up (DMU) and analysis of the entire system. Dynamic interactions among the various supplies, converters and loads are examined. System stability and performance are assessed under normal and extreme operating conditions.

The increasing power demand in vehicles has resulted in a need for a higher onboard generation capacity. With the increasing generation requirement, the torque levels of the generator are found to closely converge with that of the starter motor. Hence, integrating the two machines and using a single machine for the two purposes would be technically viable and economically advantageous. This results in a more compact design solution as well. The Integrated Starter/Alternator (ISA) will be integrated directly to the crankshaft of the Internal Combustion Engine (ICE) and deliver 5 kW average and 12-15 kW peak power at 42V.

The automotive industry is transitioning from the present 14V electrical system to a 42V system. This voltage evolution is due to the number of new systems (safety, fuel economy and customer convenience) being developed which require increased electrical power that a 14V system cannot deliver. During this transition, it will be necessary to control 14V subsystems in a 42V architecture. This paper presents 42V PWM (Pulse Width Modulation) voltage conversion and control technologies as a solution to control these 14V subsystems.